Default welcome msg!

Automation & Measurement Devices

Items 1 to 10 of 46 total

per page

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  • LJTick-RelayDriver

    Allows 2 digital I/O lines to each control a relay or other moderate load. The 4-pin design plugs into the standard DIO/DIO/GND/VS screw terminal block found on LabJacks such as the U3, U6, UE9, and T7. Each DIO controls a switch to ground (i.e. open-collector) that can hold off up to 50 volts and can sink up to 200 mA.

    • Connect LabJack VS terminal(5V) to the (+) of the load.
    • RelayDriver connects to the low side (-) of the load.
    Learn More
  • DIN Rail Mounting Clip

    Clip used to mount a LabJack device to a DIN rail.  Simply attach this clip to the backside of a LabJack device, and clip it to any DIN rail.  This clip is manufactured by TE Connectivity, p/n TKAD, or 6-1437661-4.

    Learn More
  • EI1050 Digital TemperatureHumidity Probe

    Uses two digital lines on any LabJack to retrieve temperature and relative humidity measurements. Featuring the Sensirion SHT11 sensor, it provides 14-bit temperature readings and 12-bit humidity readings. An enable line is provided to allow multiple EI-1050 probes to be connected to a single LabJack.

    • Temperature Range: -40 to +120 °C
    • Temperature Accuracy: ±0.5 °C @ 25 °C
    • Humidity Range: 0-100 %RH
    • Humidity Accuracy: ±3.5 %RH
    • Made by Electronic Innovations Corp.
    Learn More
  • EI1034 Temperature Probe

    Easy to use and very accurate temperature probe from Electronic Innovations Corp. Features a waterproof stainless-steel probe, a high-level linear output of 10 mV per degree F, a typical accuracy of ±0.4 degrees F (±0.22 degrees C) at room temperature, and a range of 0 to +230 degrees F (-17 to +110 degrees C, with U3/UE9).

    Learn More
  • EI1022 Temperature Probe

    Easy to use and inexpensive temperature probe from Electronic Innovations Corp. Features a plastic probe, a high-level linear output of 10 mV per degree K, a typical accuracy of ±1 degrees C (±1.8 degrees F) at room temperature, and a range of -40 to +100 degrees C (-40 to +212 degrees F).

    Learn More
  • LJTick-DAC

    Provides a pair of 14-bit analog outputs with a range of +/- 10 volts. Plugs into any digital I/O block, and thus up to 10 of these can be used per LabJack to add 20 analog outputs. Works with the T7 and any UD family device (U3/U6/UE9).

    Learn More
  • LJTick-VRef-25

    Voltage reference accessory that outputs a stable 2.5V. Commonly used as an excitation voltage for various circuits. The IOA and IOB lines are pass-through terminals, and do not interact with the accessory in any way.

    • Voltage: 2.5V
    • Accuracy: ±0.08%, ±2mV
    • Maximum load: 50mA
    • Short circuit current: 100mA
    • Temperature coefficient: 5ppm/°C
    Learn More
  • LJTick-LVDigitalIO

    A bidirectional logic shifting board for converting 3.3V logic down to 2.5V or 1.8V. There is also a VOUT terminal which can source power at the selected voltage. Useful for users who have external boards that run on lower logic thresholds, or simply want a 3.3V, 2.5V, or 1.8V supply. The logic terminals presented on this accessory board are for communication purposes only, they cannot drive relays or other forms of load.

    • Supports bi-directional communication
    • Up to 800kHz
    • 3.3V, 2.5V, or 1.8V
    • VOUT terminal can source up to 200mA

    Note: Advanced users may convert the 1.8V option to 5V by installing a jumper on R5, and removing or destroying U3.

    Learn More
  • LJTick-OutBuff

    Increases the output current of the DAC outputs on LabJack devices. Can also be used for switched 3.3V when attached to a 3.3V digital I/O line. LabJack devices cannot output more than about 15mA on their DAC0 and DAC1 analog outputs, so this accessory is very helpful for users who want to increase that capability. One common application is to control the speed of a low voltage DC motor.

    • Drives up to 200mA
    • 0-5V output range*

    *Max is tied to USB supply voltage, which is 5V nominally.

    Learn More
  • LJTick-VRef-41

    Voltage reference accessory that outputs a stable 4.096V. Commonly used as an excitation voltage for bridge circuits. Simply attach the supply side of the bridge to the 4.096 terminal, and ground to the GND terminal.  The IOA and IOB lines are simply pass-through terminals, and do not interact with the accessory in any way.

    • Voltage: 4.096V
    • Accuracy: ±0.08%, 3.27mV
    • Maximum load: 50mA
    • Short circuit current: 100mA
    • Temperature coefficient: 5ppm/°C
    Learn More

Items 1 to 10 of 46 total

per page

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5